Skip to main content
Burak Ozpineci is a globally recognized leader in power electronics research. He was named an ORNL Corporate Fellow in fall 2021. Credit: Carlos Jones/ORNL, U.S. Dept. of Energy

Burak Ozpineci started out at ORNL working on a novel project: introducing silicon carbide into power electronics for more efficient electric vehicles. Twenty years later, the car he drives contains those same components.

ORNL researchers observed that atomic vibrations in a twisted crystal result in winding energetic waves that govern heat transport, which may help new materials better manage heat. Credit: Jill Hemman/ORNL, U.S. Dept. of Energy

A discovery by Oak Ridge National Laboratory researchers may aid the design of materials that better manage heat.

Ten scientists from the Department of Energy’s Oak Ridge National Laboratory are among the world’s most highly cited researchers. Credit: ORNL, U.S. Dept. of Energy

Ten scientists from the Department of Energy’s Oak Ridge National Laboratory are among the world’s most highly cited researchers, according to a bibliometric analysis conducted by the scientific publication analytics firm Clarivate.

Amy Elliott, ORNL’s group leader for robotics and intelligent systems, has been honored with the ASTM International Additive Manufacturing Young Professional Award for her early career research in materials science and STEM leadership. Credit: ORNL, U.S. Dept. of Energy

Amy Elliott, a group leader for robotics and intelligent systems at Oak Ridge National Laboratory, has received the 2021 ASTM International Additive Manufacturing Young Professional Award for her early career research contributions

A material’s spins, depicted as red spheres, are probed by scattered neutrons. Applying an entanglement witness, such as the QFI calculation pictured, causes the neutrons to form a kind of quantum gauge. This gauge allows the researchers to distinguish between classical and quantum spin fluctuations. Credit: Nathan Armistead/ORNL, U.S. Dept. of Energy

A team led by the U.S. Department of Energy’s Oak Ridge National Laboratory demonstrated the viability of a “quantum entanglement witness” capable of proving the presence of entanglement between magnetic particles, or spins, in a quantum material.

ORNL researchers developed a novel process for manufacturing extreme heat resistant carbon-carbon composites at a faster rate and produced fins or strakes made of the materials for testing on a U.S. Navy rocket launching with NASA. Credit: ORNL, Sandia/U.S. Dept. of Energy

Oak Ridge National Laboratory researchers have developed a novel process to manufacture extreme heat resistant carbon-carbon composites. The performance of these materials will be tested in a U.S. Navy rocket that NASA will launch this fall.

Researchers from ORNL’s Vehicle and Autonomy Research Group created a control strategy for a hybrid electric bus that demonstrated up to 30% energy savings. Credit: University of California, Riverside

Oak Ridge National Laboratory researchers developed and demonstrated algorithm-based controls for a hybrid electric bus that yielded up to 30% energy savings compared with existing controls.

Marm Dixit, a Weinberg Distinguished Staff Fellow in the Emerging and Solid-State Batteries Group at ORNL, has received a Toyota Young Investigator Fellowship for Projects in Green Energy Technology from the Electrochemical Society. Credit: Carlos Jones/ORNL, U.S. Dept. of Energy

Marm Dixit, a Weinberg Distinguished Staff Fellow in the Emerging and Solid-State Batteries Group at ORNL, has been awarded a Toyota Young Investigator Fellowship for Projects in Green Energy Technology from the Electrochemical Society.

The 3D printed concrete smart wall installed at ORNL over the summer was monitored for energy efficiency, with preliminary results showing a minimum of 8% cost savings. Credit: ORNL, U.S. Dept. of Energy

Oak Ridge National Laboratory researchers demonstrated that cooling cost savings could be achieved with a 3D printed concrete smart wall following a three-month field test.

ORNL used novel additive manufacturing techniques to 3D print channel fasteners for Framatome’s boiling water reactor fuel assembly. Four components, like the one shown here, were installed at the TVA Browns Ferry nuclear plant. Credit: Framatome

Four first-of-a-kind 3D-printed fuel assembly brackets, produced at the Department of Energy’s Manufacturing Demonstration Facility at Oak Ridge National Laboratory, have been installed and are now under routine operating