Filter News
Area of Research
- (-) Clean Energy (188)
- (-) Functional Materials for Energy (2)
- (-) Fusion and Fission (32)
- Advanced Manufacturing (22)
- Biology and Environment (25)
- Building Technologies (1)
- Computational Biology (1)
- Computational Engineering (1)
- Computer Science (8)
- Electricity and Smart Grid (1)
- Energy Sciences (1)
- Fuel Cycle Science and Technology (1)
- Fusion Energy (10)
- Isotope Development and Production (1)
- Isotopes (26)
- Materials (90)
- Materials for Computing (10)
- National Security (23)
- Neutron Science (24)
- Nuclear Science and Technology (38)
- Nuclear Systems Modeling, Simulation and Validation (1)
- Supercomputing (53)
- Transportation Systems (2)
News Topics
- (-) 3-D Printing/Advanced Manufacturing (78)
- (-) Artificial Intelligence (9)
- (-) Composites (17)
- (-) Energy Storage (74)
- (-) Isotopes (2)
- (-) Nuclear Energy (30)
- (-) Transportation (66)
- Advanced Reactors (9)
- Big Data (5)
- Bioenergy (26)
- Biology (12)
- Biomedical (7)
- Biotechnology (4)
- Buildings (36)
- Chemical Sciences (17)
- Clean Water (8)
- Climate Change (21)
- Computer Science (26)
- Coronavirus (12)
- Critical Materials (10)
- Cybersecurity (8)
- Decarbonization (34)
- Environment (55)
- Exascale Computing (3)
- Fossil Energy (2)
- Frontier (3)
- Fusion (22)
- Grid (40)
- High-Performance Computing (7)
- Hydropower (2)
- ITER (6)
- Machine Learning (7)
- Materials (37)
- Materials Science (29)
- Mathematics (2)
- Mercury (3)
- Microelectronics (1)
- Microscopy (9)
- Molten Salt (1)
- Nanotechnology (9)
- National Security (5)
- Net Zero (4)
- Neutron Science (12)
- Partnerships (13)
- Physics (2)
- Polymers (11)
- Quantum Science (2)
- Renewable Energy (1)
- Security (7)
- Simulation (7)
- Space Exploration (4)
- Statistics (1)
- Summit (4)
- Sustainable Energy (71)
- Transformational Challenge Reactor (3)
Media Contacts
Researchers at ORNL are extending the boundaries of composite-based materials used in additive manufacturing, or AM. ORNL is working with industrial partners who are exploring AM, also known as 3D printing, as a path to higher production levels and fewer supply chain interruptions.
ORNL researchers determined that a connected and automated vehicle, or CAV, traveling on a multilane highway with integrated traffic light timing control can maximize energy efficiency and achieve up to 27% savings.
In fiscal year 2023 — Oct. 1–Sept. 30, 2023 — Oak Ridge National Laboratory was awarded more than $8 million in technology maturation funding through the Department of Energy’s Technology Commercialization Fund, or TCF.
The heat is on at this year’s Molten Salt Reactor Workshop – where top research and industry minds are melding to advance development on molten salt technology – at ORNL.
The Department of Energy’s Oak Ridge National Laboratory hosted the second 2023 cohort of the International Atomic Energy Agency’s Lise Meitner Programme in October.
Steven Campbell can often be found deep among tall cases of power electronics, hunkered in his oversized blue lab coat, with 1500 volts of electricity flowing above his head. When interrupted in his laboratory at ORNL, Campbell will usually smile and duck his head.
An Oak Ridge National Laboratory-developed advanced manufacturing technology, AMCM, was recently licensed by Orbital Composites and enables the rapid production of composite-based components, which could accelerate the decarbonization of vehicles
ORNL has been selected to lead an Energy Earthshot Research Center, or EERC, focused on developing chemical processes that use sustainable methods instead of burning fossil fuels to radically reduce industrial greenhouse gas emissions to stem climate change and limit the crisis of a rapidly warming planet.
The common sounds in the background of daily life – like a refrigerator’s hum, an air conditioner’s whoosh and a heat pump’s buzz – often go unnoticed. These noises, however, are the heartbeat of a healthy building and integral for comfort and convenience.
Oak Ridge National Laboratory researchers have conducted a comprehensive life cycle, cost and carbon emissions analysis on 3D-printed molds for precast concrete and determined the method is economically beneficial compared to conventional wood molds.