Filter News
Area of Research
- (-) Clean Energy (76)
- (-) Energy Sciences (1)
- (-) Materials (26)
- Advanced Manufacturing (13)
- Biology and Environment (28)
- Building Technologies (3)
- Climate and Environmental Systems (1)
- Computational Biology (1)
- Computational Engineering (2)
- Computer Science (10)
- Electricity and Smart Grid (1)
- Fusion and Fission (2)
- Fusion Energy (3)
- Isotopes (3)
- Materials for Computing (5)
- Mathematics (1)
- National Security (7)
- Neutron Science (3)
- Nuclear Science and Technology (2)
- Quantum information Science (3)
- Sensors and Controls (1)
- Supercomputing (23)
News Type
News Topics
- (-) 3-D Printing/Advanced Manufacturing (36)
- (-) Big Data (2)
- (-) Biomedical (3)
- (-) Computer Science (11)
- (-) Grid (21)
- (-) Physics (8)
- (-) Polymers (9)
- (-) Sustainable Energy (34)
- Advanced Reactors (1)
- Artificial Intelligence (1)
- Bioenergy (5)
- Biology (3)
- Biotechnology (1)
- Buildings (19)
- Chemical Sciences (6)
- Clean Water (5)
- Climate Change (8)
- Composites (9)
- Coronavirus (7)
- Critical Materials (9)
- Cybersecurity (2)
- Decarbonization (12)
- Energy Storage (35)
- Environment (23)
- Fusion (3)
- High-Performance Computing (1)
- Hydropower (2)
- Isotopes (2)
- Machine Learning (2)
- Materials (27)
- Materials Science (30)
- Mathematics (2)
- Mercury (2)
- Microscopy (10)
- Molten Salt (1)
- Nanotechnology (12)
- National Security (1)
- Net Zero (2)
- Neutron Science (7)
- Nuclear Energy (6)
- Quantum Computing (2)
- Quantum Science (1)
- Security (2)
- Simulation (1)
- Space Exploration (3)
- Statistics (1)
- Summit (1)
- Transportation (37)
Media Contacts
Steven Campbell can often be found deep among tall cases of power electronics, hunkered in his oversized blue lab coat, with 1500 volts of electricity flowing above his head. When interrupted in his laboratory at ORNL, Campbell will usually smile and duck his head.
An Oak Ridge National Laboratory-developed advanced manufacturing technology, AMCM, was recently licensed by Orbital Composites and enables the rapid production of composite-based components, which could accelerate the decarbonization of vehicles
Oak Ridge National Laboratory researchers have conducted a comprehensive life cycle, cost and carbon emissions analysis on 3D-printed molds for precast concrete and determined the method is economically beneficial compared to conventional wood molds.
After being stabilized in an ambulance as he struggled to breathe, Jonathan Harter hit a low point. It was 2020, he was very sick with COVID-19, and his job as a lab technician at ORNL was ending along with his research funding.
ORNL researchers, in collaboration with Enginuity Power Systems, demonstrated that a micro combined heat and power prototype, or mCHP, with a piston engine can achieve an overall energy efficiency greater than 93%.
Andrea Delgado is looking for elementary particles that seem so abstract, there appears to be no obvious short-term benefit to her research.
Chemist Jeff Foster is looking for ways to control sequencing in polymers that could result in designer molecules to benefit a variety of industries, including medicine and energy.
A new report published by ORNL assessed how advanced manufacturing and materials, such as 3D printing and novel component coatings, could offer solutions to modernize the existing fleet and design new approaches to hydropower.
Scientists at ORNL developed a competitive, eco-friendly alternative made without harmful blowing agents.
ORNL researchers Ben Ollis and Max Ferrari will be in Adjuntas to join the March 18 festivities but also to hammer out more technical details of their contribution to the project: making the microgrids even more reliable.