Filter News
Area of Research
- (-) Clean Energy (91)
- (-) Computational Engineering (1)
- (-) Materials for Computing (6)
- (-) National Security (8)
- Advanced Manufacturing (15)
- Biology and Environment (24)
- Building Technologies (3)
- Computer Science (7)
- Electricity and Smart Grid (2)
- Energy Sciences (1)
- Functional Materials for Energy (1)
- Fusion and Fission (12)
- Fusion Energy (6)
- Materials (30)
- Neutron Science (3)
- Nuclear Science and Technology (6)
- Quantum information Science (4)
- Sensors and Controls (1)
- Supercomputing (13)
News Type
News Topics
- (-) 3-D Printing/Advanced Manufacturing (48)
- (-) Critical Materials (6)
- (-) Fusion (2)
- (-) Grid (25)
- (-) Machine Learning (7)
- (-) Molten Salt (1)
- (-) Quantum Science (2)
- (-) Sustainable Energy (41)
- Advanced Reactors (3)
- Artificial Intelligence (7)
- Big Data (7)
- Bioenergy (8)
- Biology (6)
- Biomedical (4)
- Biotechnology (1)
- Buildings (22)
- Chemical Sciences (8)
- Clean Water (5)
- Climate Change (12)
- Composites (11)
- Computer Science (20)
- Coronavirus (11)
- Cybersecurity (10)
- Decarbonization (14)
- Energy Storage (43)
- Environment (30)
- Frontier (1)
- High-Performance Computing (3)
- Hydropower (2)
- Isotopes (1)
- Materials (27)
- Materials Science (25)
- Mathematics (2)
- Mercury (2)
- Microscopy (7)
- Nanotechnology (8)
- National Security (15)
- Net Zero (2)
- Neutron Science (7)
- Nuclear Energy (5)
- Partnerships (2)
- Physics (2)
- Polymers (8)
- Security (7)
- Simulation (2)
- Space Exploration (3)
- Statistics (1)
- Summit (2)
- Transformational Challenge Reactor (1)
- Transportation (44)
Media Contacts
It would be a challenge for any scientist to match Alexey Serov’s rate of inventions related to green hydrogen fuel. But this researcher at ORNL has 84 patents with at least 35 more under review, so his electrifying pace is unlikely to slow down any time soon.
The Hub & Spoke Sustainable Materials & Manufacturing Alliance for Renewable Technologies, or SM2ART, program has been honored with the composites industry’s Combined Strength Award at the Composites and Advanced Materials Expo, or CAMX, 2023 in Atlanta. This distinction goes to the team that applies their knowledge, resources and talent to solve a problem by making the best use of composites materials.
Steven Campbell can often be found deep among tall cases of power electronics, hunkered in his oversized blue lab coat, with 1500 volts of electricity flowing above his head. When interrupted in his laboratory at ORNL, Campbell will usually smile and duck his head.
An Oak Ridge National Laboratory-developed advanced manufacturing technology, AMCM, was recently licensed by Orbital Composites and enables the rapid production of composite-based components, which could accelerate the decarbonization of vehicles
Sreenivasa Jaldanki, a researcher in the Grid Systems Modeling and Controls group at the Department of Energy’s Oak Ridge National Laboratory, was recently elevated to senior membership in the Institute of Electrical and Electronics Engineers, or IEEE.
Oak Ridge National Laboratory researchers have conducted a comprehensive life cycle, cost and carbon emissions analysis on 3D-printed molds for precast concrete and determined the method is economically beneficial compared to conventional wood molds.
After being stabilized in an ambulance as he struggled to breathe, Jonathan Harter hit a low point. It was 2020, he was very sick with COVID-19, and his job as a lab technician at ORNL was ending along with his research funding.
After completing a bachelor’s degree in biology, Toya Beiswenger didn’t intend to go into forensics. But almost two decades later, the nuclear security scientist at ORNL has found a way to appreciate the art of nuclear forensics.
Yarom Polsky, director of the Manufacturing Science Division, or MSD, at the Department of Energy’s Oak Ridge National Laboratory, has been elected a Fellow of the American Society of Mechanical Engineers, or ASME.
A new report published by ORNL assessed how advanced manufacturing and materials, such as 3D printing and novel component coatings, could offer solutions to modernize the existing fleet and design new approaches to hydropower.