Filter News
Area of Research
- (-) Clean Energy (55)
- (-) Materials (23)
- (-) Supercomputing (5)
- Advanced Manufacturing (11)
- Biology and Environment (18)
- Building Technologies (1)
- Climate and Environmental Systems (3)
- Computational Engineering (1)
- Computer Science (3)
- Electricity and Smart Grid (1)
- Fusion Energy (2)
- Materials for Computing (6)
- Mathematics (1)
- National Security (3)
- Neutron Science (4)
- Quantum information Science (1)
- Sensors and Controls (1)
- Transportation Systems (1)
News Topics
- (-) 3-D Printing/Advanced Manufacturing (26)
- (-) Environment (18)
- (-) Grid (15)
- (-) Materials Science (23)
- Advanced Reactors (2)
- Artificial Intelligence (2)
- Big Data (5)
- Bioenergy (2)
- Biology (3)
- Biomedical (6)
- Biotechnology (1)
- Buildings (13)
- Chemical Sciences (4)
- Clean Water (4)
- Climate Change (7)
- Composites (9)
- Computer Science (23)
- Coronavirus (5)
- Critical Materials (10)
- Decarbonization (4)
- Energy Storage (23)
- Exascale Computing (1)
- Frontier (1)
- Fusion (3)
- High-Performance Computing (3)
- Hydropower (2)
- Isotopes (2)
- Machine Learning (3)
- Materials (22)
- Mathematics (1)
- Mercury (1)
- Microscopy (6)
- Molten Salt (1)
- Nanotechnology (8)
- Net Zero (1)
- Neutron Science (4)
- Nuclear Energy (5)
- Physics (2)
- Polymers (8)
- Quantum Computing (4)
- Quantum Science (4)
- Simulation (2)
- Space Exploration (4)
- Statistics (1)
- Summit (6)
- Sustainable Energy (28)
- Transportation (27)
Media Contacts
An Oak Ridge National Laboratory-developed advanced manufacturing technology, AMCM, was recently licensed by Orbital Composites and enables the rapid production of composite-based components, which could accelerate the decarbonization of vehicles
Oak Ridge National Laboratory researchers have conducted a comprehensive life cycle, cost and carbon emissions analysis on 3D-printed molds for precast concrete and determined the method is economically beneficial compared to conventional wood molds.
Researchers from Oak Ridge National Laboratory and Northeastern University modeled how extreme conditions in a changing climate affect the land’s ability to absorb atmospheric carbon — a key process for mitigating human-caused emissions. They found that 88% of Earth’s regions could become carbon emitters by the end of the 21st century.
A new report published by ORNL assessed how advanced manufacturing and materials, such as 3D printing and novel component coatings, could offer solutions to modernize the existing fleet and design new approaches to hydropower.
ORNL researchers Ben Ollis and Max Ferrari will be in Adjuntas to join the March 18 festivities but also to hammer out more technical details of their contribution to the project: making the microgrids even more reliable.
Warming a crystal of the mineral fresnoite, ORNL scientists discovered that excitations called phasons carried heat three times farther and faster than phonons, the excitations that usually carry heat through a material.
When aging vehicle batteries lack the juice to power your car anymore, they may still hold energy. Yet it’s tough to find new uses for lithium-ion batteries with different makers, ages and sizes. A solution is urgently needed because battery recycling options are scarce.
ORNL researchers have identified a mechanism in a 3D-printed alloy – termed “load shuffling” — that could enable the design of better-performing lightweight materials for vehicles.
The presence of minerals called ash in plants makes little difference to the fitness of new naturally derived compound materials designed for additive manufacturing, an Oak Ridge National Laboratory-led team found.
Researchers at Oak Ridge National Laboratory have designed architecture, software and control strategies for a futuristic EV truck stop that can draw megawatts of power and reduce carbon emissions.