Corrugated Fiberboard, Triple Wall Box QC Checklist
8-1/8 x 8-1/8 x 8-1/8 inches
| Description | Stores
Catalog Number |
Packaging
Filling Instructions |
Plant |
| Box, Shipping, Regular
Slotted Carton (RSC), Corrugated Fiberboard, Triplewall, with 2 support dividers UN 4G /Y 30/ S, Size: 8-1/8 x 8-1/8 x 8-1/8 inches |
02-114-9900 | LMTPM-CHK-42 (for Hazmat use) or LMTPM-PKG-06 (for RAMSPAC use) |
ORNL |
Mfg. Details per: LMER
Packaging Specifications
No. 631-4GO-0001
Issue Date: December 10, 1997
Revised Date: June 15, 1999
The following inspections will be performed on incoming boxes by receiver to determine the boxes meet quality standards and the requirements of this document. However, the receiver is not limited to the following inspections to determine quality and specification conformance. Conformance will be indicated by a Y or N in the "Y/N" column, and negative responses documented on the Nonconformance Report (NCR), UCN 11457, (items 3-21b), attached to the checklist, and submitted to Lockheed Martin Transportation and Packaging Management (LMTPM) for necessary action.
This checklist is to be reproduced for QC Inspections.
Receiver Inspection Quality Control (QC) Checklist for Incoming Corrugated Boxes |
|||
QC Conformance |
Y/N |
<< "No's" to be documented on form UCN-11457 with checklist |
|
1 |
Dimensions | Stated inside dimensions (from score) are correct for specified box size. | |
2 |
Fiberboard Surface | Clean, no significant scuffing, breaks/cuts in board, corrugation does not protrude past linerboard surface. | |
3 |
Scoring/score lines | Uniform, and sufficient depth to allow clean fold, without distortion. | |
| No surface breaks in the score lines, when flaps folded. | |||
4 |
Corrugating Medium | Medium not crushed within the assembled box. | |
5 |
Box Flaps | When folded along score lines, inside flaps meet, and are square – spacing between exterior flaps no greater than 1/4". | |
6 |
Manufacturer's joint | Metal staples closed, without breaking linerboard, and points/edges not protruding to snag/puncture inner packagings. | |
7 |
Box Alignment | Assembled box and top are square at corners/edges. | |
8 |
Support Dividers | Two each doublewall furnished per box with order. | |
| Corrugated board is scored, and cut for assembly. | |||
9 |
Markings | Boxes marked (as a minimum) with LMER specified UN markings, per Catalog Description. | |
| Boxes legibly marked (printed) per required UN markings, and with boxmaker's certificate for the specified box strength, and Rule 41/222 markings. | |||
10 |
Printing | Printing on the box is of the specified size, is sharp, contains no smears, and is located according to specifications. | |
| Size, CATN—plus last four (4) digits of catalog number on bottom per ¶ 2.11. | |||
11 |
Water Resistance | Documentation furnished with shipment per ¶ 2.7. | |
| Catalog Number___________________________ | P. O. Number________________________________ |
| Total Units Received_______________________ | Inspection Method: Per LMTPM QC Inspection Plan |
| Sample Size_______[Based on ANSI/ASQC Z1.4-1993] | NCR No._______________________ |
| Inspector/Date_________________________________ | Additional comments on back: _____check, if yes. |
The above QC check list shall be accomplished for each order based on random samples of incoming boxes, by QC personnel to determine manufacturer's conformance to these specified Packaging Specifications.
Shipments of corrugated boxes not meeting specified requirements will be returned to the seller for credit.
QC inspections resulting in non-compliance with the Packaging Specification will be cause for rejection of the entire shipment.
[TPM
Home] [ORNL Home] [Disclaimer]
[Website
Comments] [Contact
Us] |